|
The Lamborghini V10 is a ninety degree (90°) V10 petrol engine which was developed for the Lamborghini Gallardo automobile, first sold in 2003. Developed by AUDI AG, for use in the Gallardo, and the first engine developed for Automobili Lamborghini S.p.A. after they were acquired by AUDI AG - part of the Volkswagen Group. Its crankcase and cylinder block is built at the Audi Hungaria Motor Kft. factory in Győr, Hungary,〔(【引用サイトリンク】title=Lamborghini Cars full specifications - First spyshots of the Lamborghini L140 model )〕 whilst final assembly is at Sant'Agata, Italy. It has a 90° vee angle and unusually for a production motor a dry sump lubrication system was chosen to keep the center of gravity of the engine low. There was also some speculation that the engine block of the original 5.0 litre Lamborghini V10 is closely based on the Audi 4.2 FSI V8, which Audi produces for their luxury cars. However, this was denied by AUDI AG, in their official documentation for their 5.2 FSI V10 engine, as used in the Audi S6 and Audi S8 - the Lamborghini 5.0 V10 has a cylinder bore spacing of between centres, whereas the Audi 5.2 V10 cylinder bore spacing is . The cylinder heads use the four valves per cylinder layout favoured by the Italian firm, rather than the five valve per cylinder variation formerly favoured by the German members of Volkswagen Group - including Audi and Volkswagen Passenger Cars. It was later confirmed by Stefan Reil of Audi's quattro GmbH subsidiary that the new 5.2 litre Lamborghini V10 does share technologies with the Audi 5.2 V10 engine, as is evident by Lamborghini's usage of Audi's Fuel Stratified Injection, and 90 mm cylinder spacing.〔 〕 ==Specifications== ;engine configuration: 90° V10 engine; dry sump lubrication system ;engine displacement etc. :5.0 — ; bore x stroke: (stroke ratio: 0.89:1 - undersquare/long-stroke), 496.1 cc per cylinder; compression ratio: 11.5:1〔 :5.2 — ; bore x stroke: (stroke ratio: 0.91:1 - undersquare/long-stroke), 520.4 cc per cylinder; compression ratio: 12.5:1〔 ;cylinder block and crankcase :5.0 — cast aluminium alloy with integrated liners with eutectic alloy; cylinder bore spacing;〔 forged steel crankshaft with split crankpins (to create even 72 deg firing interval with the 90 deg vee-angle)〔 :5.2 — cast aluminium alloy; 90 mm cylinder bore spacing; forged steel crankshaft with shared crankpins (creating an uneven firing interval of either 54 deg or 90 deg separation)〔 ;cylinder heads and valvetrain: cast aluminium alloy, four valves per cylinder, 40 valves total, low-friction roller cam followers with automatic hydraulic valve clearance compensation, chain driven double overhead camshafts, continuously variable valve timing system both for intake and exhaust ;aspiration: two air filters, two hot-film air mass meters, two cast alloy throttle bodies each with electronically controlled 'drive by wire' throttle butterfly valves, cast magnesium alloy variable geometry and resonance intake manifold ;fuel system :5.0 — two linked common rail fuel distributor rails, electronic sequential multi-point indirect fuel injection with 10 intake manifold-sited fuel injectors :5.2 — fully demand-controlled and returnless; fuel tank mounted low pressure fuel pump, Fuel Stratified Injection (FSI):〔 two inlet camshaft double-cam driven single-piston high-pressure injection pumps maintaining pressure in the two stainless steel common rail fuel distributor rails, ten combustion chamber sited direct injection solenoid-controlled sequential fuel injectors〔 ;ignition system and engine management: mapped direct ignition with centrally mounted spark plugs and ten individual direct-acting single spark coils; two Lamborghini LIE electronic engine control unit (ECUs) working on the 'master and slave' concept due to the high revving nature of the engine ;exhaust system :5.0 — five-into-one exhaust manifolds for each cylinder bank :5.2 — 2-1-2 branch exhaust manifold per cylinder bank〔 to minimise reverse pulsation of expelled exhaust gasses ;5.0 power and torque outputs and applications : @ 7,800 rpm; @ 4,500 rpm (80% available from 1,500 rpm) — Gallardo 2003-2005 : @ 8,000 rpm; @ 4,250 rpm — Gallardo SE, Spyder, and 2006-2014 : @ 8,000 rpm; @ 4,250 rpm — Gallardo Superleggera ;5.2 power and torque outputs and applications : @ 8,000 rpm; @ 6,500 rpm — Gallardo LP560/4 - 2008-2014 : @ 8,250 rpm; @ 6,500 rpm — Huracán LP610/4 - 2014-on 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Lamborghini V10」の詳細全文を読む スポンサード リンク
|